• Home
  • F130 Elite Front Loading Digital Kiln w/ Side Elements - BLACK - 120 Volt - Width: 11.0" - Height: 13.0" - Depth: 11.0" - Paragon

F130 Elite Front Loading Digital Kiln w/ Side Elements - BLACK - 120 Volt - Width: 11.0" - Height: 13.0" - Depth: 11.0" - Paragon

10 Reviews
SKU: PKF130 DIGI BLACK
$2,098.05

$2,331.17 Retail
$233.12 Savings
FREE SHIPPING!*

Details

You can make figurines up to 12” tall in the F-130. Anneal large glass beads and marbles. Raise the spring-loaded vertical-drop door to insert a glass figurine with a punty rod. Lower the door. The punty rod will extend outside the firing chamber through the smaller 4” x 8” punty rod door. This allows even large glass pieces to anneal safely.

Enjoy the glittering beauty of dichroic glass. This kiln will give you a haven of creative enjoyment that will immerse you for many years. Imagine how it could change your life style.

 

Thick firebricks; sidewall element

 

The firebricks in the roof, walls, door, and bottom are 3” thick. This is 20% more insulation than the standard 2 1/2” firebricks in the walls and bottom of our earlier F-130 kilns. The extra insulation enables the F-130 to maintain a temperature hold with greater ease. Sidewall heat is now standard in the F-130. The element heats from the sides and back of the kiln in dropped, recessed wall grooves.

 

Deluxe door gaskets

 

Because of a gap under the small punty rod door, you can usually close the door all the way even when mandrels extend past the firing chamber. This helps to retain the heat in the kiln. Powerful, rare-earth magnets hold the punty rod door in the open and closed positions. To further retain heat, the 4” x 8” punty rod door is 2” thick and includes two woven, flexible high-temperature gaskets.

 

Slide-out mandrel holder

 

The mandrel holder can be adjusted horizontally and vertically without tools. Position the heavy-duty welded mandrel holder anywhere from 4 1/2” to 13” in front of the main section of kiln floor. (Note: The firebrick extension on the front of the kiln extends 3” beyond the front edge of the kiln floor.) Then tighten the mandrel holder with thumb screws. The holder slides inside steel tubes in the base of the kiln. The stainless steel mandrel rest, which includes 7 slots, can be adjusted vertically.

 

Sloped control panel

 

The control panel is angled for easy viewing and operation of the digital controller. Program the kiln from a comfortable position. The controller, pilot light, and switch are mounted on a brushed stainless steel plate. Gain easy access to the electrical components by removing the front panel.

 

Stainless steel rod warmer

 

To save production time, pre-heat glass rods on top of the kiln. The 5” long stainless steel rod warmer is slotted for five rods.

 

Made in America

 

The kiln is made at the Paragon factory in Mesquite, Texas, which is about 20 minutes east of Dallas. Our kilns are not merely assembled—they are hand crafted.

 

Features of the F-130

- On/off switch; easily reboot the controller.

- Safety pilot light

- Dropped, recessed sidewall element grooves

- 3” insulating refractory firebricks in the roof, walls and bottom

- Electrical components stay cool in a slotted base.

- Precisely balanced spring-loaded vertical-drop door

- Double gaskets under the 2" thick, 4” x 8” punty rod door

- Rare earth magnets hold the punty rod door open or closed.

- Stainless steel sheet metal screws

- TUV tested to UL and CSA standards.

- Made in the USA

 

Thermocouple with “special limit” wire


The thermocouple senses temperature inside the kiln. It is the small rod that extends into the firing chamber. The ¼” wide Type-K, 14-gauge, exposed-tip thermocouple is made with special-limit wire for superior accuracy. The exposed tip gives the controller a fast response time for even temperatures during holds. The thermocouple is made in America to our exacting standards.

 

Designed for production

 

Paragon’s warranty is not affected by frequency of use. Fire your new kiln every day if you want, even in commercial settings. That will have no effect on the warranty period.

 

Specifications:

- Warranty: Two Year Limited Warranty

- Max Temp: 1700° F | 926° C

- Voltage: 120

- Amps: 20

- Phase: 1

- Hertz: 60

- Watts: 2400

- Cordset: NEMA 5-20R

- Controller: Sentry Xpress 4.0 Digital 3-Key

- Kiln Type: Front Loading Square

- Sides: 4

 

Chamber Dimensions:

- Chamber Volume: 0.90 CU.FT. | 25.49 Liters

- Width: 11.0″ - 279mm

- Depth: 11.0″ - 279mm

- Height: 13.0″ - 330mm

- Outer Size: 22.0″W x 26.0″D x 28.75″H | 559W x 660D x 730H mm

- Ship Size: 32.0″W x 34.0″D x 39.0″H | 813W x 864D x 991H mm

Ratings & Reviews

10 reviews

  • 4 stars
  • 0 reviews
  • 3 stars
  • 0 reviews
  • 2 stars
  • 0 reviews
  • 1 star
  • 0 reviews

Paragon f130.

by

I knew that when I purchased my paragon f130,I had made the right decision. the easy to follow instructions. The great customer service that I received from Mountain glass the buying process could not have been easier. I look forward to the many years of using it thank you so much